How To Repair Crack In Guitar

Repair cracks in tops and sides of an acoustic guitar.

These tools are for repairing stubborn cracks, splits and punctures in acoustic guitars.

Use this kit to:

• Pull ii sides of a divide together so they're level and prepare for repair
• Pull crunches and punctures into shape for gluing
• Create thin, uniform repair cleats (patches)
• Clamp and mucilage cleats in place

Crack repair using wooden repair cleats

Our hardened-steel Cleat Cutter creates thin round cleats of wood to be glued beyond a crack on the inside of a guitar. The Scissure Clamp uses a thin wire to pull the cleat into place. The cleat's woodgrain runs beyond the crack, non parallel to it, creating a strong repair that's as well very small.

How to employ the crack repair tools

Cut your repair cleats from matching wood

Use the Cleat Cutter in a drill press to make cleats from woods that'due south similar to what you're repairing. The thickness of the woods should exist no less than 3/32" and no more than than one/8".

Make a caul to level the sides of the crack

On the outside of the repair, a caul applies fifty-fifty pressure to make both sides of the scissure uniformly level. Every crack repair is dissimilar in length and shape, then each repair chore needs a caul that'due south sized to fit. You'll need to make a caul shaped to fit your repair.

Make cauls out of acrylic, or wood wrapped in nonstick plastic or waxed paper. The size depends on the shape of the cleft and whether it requires i Crack Clamp or several.

Keep the surfaces make clean

Inspect the scissure for dirt, lacquer chips or other debris. Use compressed air to remove particles.

Thread the wire

Put a short length of our .014" wire supplied into the pin vise, leaving about i/4" exposed. Use this to pierce a hole through the crack where the Crack Clamp will be placed.

Cut a piece of wire long enough to run in through the pierced pigsty and dorsum out through the guitar's soundhole. A piece of tape on this wire volition keep it from slipping into the guitar.

Thread a wooden cleat onto the cease of the wire. The non-askew side is the gluing surface that will contact the repair.

Add the contumely ballast. Thread the wire through lengthwise, so add a couple loops through the cross holes to secure it.

Do a dry out run

At this stage, do dry-clamp exam. A dry run shows you how much tension it takes to close the crack. Find this out before applying gum, so you have no surprises subsequently when working fast with wet glue.

Pump glue into the scissure

Work glue into the crack from the exterior, using the air gun. Pressure of 10psi is sufficient to push button most glues. Don't overdo the pressure: you don't want mucilage running out the opposite side of the repair. Paper towels within the guitar will catch drips. Clean upwards whatsoever excess glue, inside and outside.

Mucilage the cleat

Use gum to the cleat and pull the wire to bring the cleat into contact with the crack on the within of the guitar.

Tighten the Fissure Clench

On the outside, thread the caul onto the wire. Wrap the wire around the tuner shaft and carefully tighten the wire, pulling the cleft together until the ii sides are level.

You want the grain on the cleat to sit at approximately 45 degrees to the crack, providing strength to resist the forces that created the crack originally. Use a mirror within the guitar to run across that it'south oriented this style before yous terminate tightening. Make clean upward whatsoever glue squeezeout.

When your mucilage has dried, the fissure repair is consummate, with the small wooden cleat(s) belongings it shut permanently.

The minor hole left by the wire tin can be patched with glue or matching filler. After removing the clamp and wire there will be a small-scale hole(s) left from where the wire passed through the repair if it was a tight crack. This hole can be patched with gum or matching filler.

Sometimes, a scissure that'due south been repaired is still missing bits of forest. A gap like this tin can be filled with a sliver of matching wood or woods filler.

Source: https://www.stewmac.com/video-and-ideas/online-resources/learn-about-repair-tools-and-repair-techniques/stewmac-crack-repair-tool-instructions/

Posted by: tayloraffhand1945.blogspot.com

Share this post